Trim Tabs?

This forum is for comments and the exchange of information relating to Trojan Runabouts.

Note: Negative or inflammatory postings will not be tolerated.

Moderators: BeaconMarineBob, Moderator, BeaconMarineDon

Post Reply
User avatar
61SkiBee
Sporadic User
Posts: 99
Joined: Sat Mar 26, 2005 7:21 pm
Location: Minnesota

Trim Tabs?

Post by 61SkiBee »

As I get closer and closer (ever closer) to putting my '61 SkiBee inboard on the water, I am pondering whether to re-attach the "Trim Tabs" that were attached to the bottom of the transom when I got the boat.

They are just small aluminum plates with a flexible "fin" on the bottom that is set to whatever pitch you choose via bolts. Of course, there is no "set" left to them as the bolts are steel and are permanently bonded to the aluminum. Rather than mess around drilling them out, I just left them set the way they were.

A couple of seasons ago, I removed the "tabs." They were held on by six screws and, of course, the screws were steel, rusted away, and too long--poking through the board into the boat.

I thought the "tabs" might be affecting handling when turning at speed, so I puttied up the screw holes and tried it without them. Didn't seem to make much difference.

Anyone have any experience with these Trim Tabs? I believe their sole purpose is to help lift the tail out of the water faster and get up on plane easier. I can't really notice much difference, but it's kind of hard to do an apples-to-apples comparison with them off or on.
Guy Strauss

"Das Boot"
'61 SkiBee, 17' Inboard Runabout ski tow
Ford 292 Interceptor (pictured)
User avatar
k9th
Ultimate User
Posts: 1615
Joined: Fri Oct 31, 2008 10:31 pm
Location: Michigan City, IN

Post by k9th »

Unless you are up for re-setting them, I would remove them permanently as they will probably end up contributing parasitic drag to the boat if left to move around freely on their own.
Tim

"SeaDog"
1979 36' Tri-Cabin
User avatar
61SkiBee
Sporadic User
Posts: 99
Joined: Sat Mar 26, 2005 7:21 pm
Location: Minnesota

Post by 61SkiBee »

Thanks for the heads-up. I have returned the old Bee to the water, and left the tabs as is for now, since I had no way of knowing how to set them up any differently, and they make dandy through-the-wood support for the bottom of the transom. They might get it up on plane a little more easily by providing some lift, but once I'm up on plane, they're clear of the water, so no drag when cruising. If anyone asks, I'll just call 'em "spoilers." They got BIG BRASS SCREWS now! :D

So far, the boat is holding up pretty well, but I'm woefully behind on finishing work. I'm afraid if I started that now, it would make for a very dry summer.
Guy Strauss

"Das Boot"
'61 SkiBee, 17' Inboard Runabout ski tow
Ford 292 Interceptor (pictured)
User avatar
k9th
Ultimate User
Posts: 1615
Joined: Fri Oct 31, 2008 10:31 pm
Location: Michigan City, IN

Post by k9th »

Glad you got it resolved.. I agree, you have to do your boating while you can. The season for those of us up north is very short and you can always work on it through the winter.
Tim

"SeaDog"
1979 36' Tri-Cabin
User avatar
61SkiBee
Sporadic User
Posts: 99
Joined: Sat Mar 26, 2005 7:21 pm
Location: Minnesota

Post by 61SkiBee »

k9th,

While nothing is ever really "resolved" on a 49-year-old wooden boat, there has been some improvement for now, I think

Speaking of putting boats in when you can, and how hard it is with a barely 6-month season up here, it's remarkable that Minnesota, at least in the past few years, has had more boats per capita than any other state, including all the coastal states. Heck, water skiing was even invented here. Keep those Norwegians cooped up all winter, and they yust go crazy when the water opens.
Guy Strauss

"Das Boot"
'61 SkiBee, 17' Inboard Runabout ski tow
Ford 292 Interceptor (pictured)
Post Reply